Programming H6105-D - Revision history

Andrea: /* USB port */

2017-06-16T13:47:19Z

‎USB port

Andrea: /* USB port */

2017-06-16T00:36:37Z

‎USB port

Andrea: /* Programming */

2017-06-15T15:31:44Z

‎Programming

Andrea: /* Serial Port */

2017-06-15T15:27:17Z

‎Serial Port

Andrea at 14:42, 15 June 2017

2017-06-15T14:42:24Z

Andrea: /* Entering disk mode 1 */

2017-06-15T14:15:38Z

‎Entering disk mode 1

Andrea: /* Hawrdware connection */

2017-06-15T14:14:00Z

‎Hawrdware connection

Andrea: Creata pagina con "this section explain how to connect and dowanload a PAWN program to the H6105-D master = Hawrdware connection = we need to make two connections: * use the USB to Seri..."

2017-06-15T14:13:39Z

Creata pagina con "this section explain how to connect and dowanload a PAWN program to the H6105-D master = Hawrdware connection = we need to make two connections: * use the USB to Seri..."

New page

this section explain how to connect and dowanload a PAWN program to the [[H6105-D]] master

= Hawrdware connection =

we need to make two connections:

* use the USB to Serial adapter to connect to the serial port

* use the USB Type-B cable to connect to the USB port

= Functions of the ports =

== Serial Port ==

on the serial port we will find the Console with the command promt <code>cp></code>
pressing the ENTER key will show a help message

== USB port ==

the USB port has tree operating modes:

* '''libusb''', this mode is active when the script is running and can be used to give the control of the system to a PC program
* '''disk mode 1''', this mode is active when the script is not running and can be used to flash a new PAWN program
* '''disk mode 2''', this mode is active during the firmware update and can be usd to flash a new firmware

= Entering disk mode 1 =

to enter in disk mode 1 you must stop a running script with the <code>script stop</code> command
at this point you should see a new usb disk unit connected to your PC named <code>HYDCPAMXDRV</code>
inside this disk there is only one file named <code>PRMGFILE.AMX</code>
first delete this file then copy the new one
when the copy is done you can:

* start your new program with <code>script run</code>
* reset the board with <code>reset</code>

@@ Line 33: / Line 33: @@
 = Programming =
-enter in disk mode 1 with the <code>script stop</code> command
+follow this steps to download a new program into the board:
-at this point you should see a new usb disk unit connected to your PC named <code>HYDCPAMXDRV</code>
+* enter in disk mode 1 with the <code>script stop</code> command
+* at this point you should see a new usb disk unit connected to your PC named <code>HYDCPAMXDRV</code> inside this disk there is only one file named <code>PRMGFILE.AMX</code>
-inside this disk there is only one file named <code>PRMGFILE.AMX</code>
+* delete this file then copy the new one
+* start your new program with <code>script run</code> or reset the board with <code>reset</code>

← Older revision		Revision as of 15:27, 15 June 2017
Line 19:		Line 19:
	pressing the ENTER key will show a help message		pressing the ENTER key will show a help message

		+	[[File:Cp-console.png]]

	== USB port ==		== USB port ==

@@ Line 23: / Line 23: @@
 == USB port ==
-the USB port has tree operating modes:
+the USB port has three operating modes:
 * '''libusb''', this mode is active when the script is running and can be used to give the control of the system to a PC program

@@ Line 27: / Line 27: @@
 * '''libusb''', this mode is active when the script is running and can be used to give the control of the system to a PC program
 * '''disk mode 1''', this mode is active when the script is not running and can be used to flash a new PAWN program
-* '''disk mode 2''', this mode is active during the firmware update and can be usd to flash a new firmware
+* '''disk mode 2''', this mode is active during the firmware update and can be used to flash a new firmware
 = Programming =

@@ Line 3: / Line 3: @@
-= Hawrdware connection =
+= Hardware connection =
 we need to make two connections:
@@ Line 10: / Line 10: @@
 * use the USB Type-B cable to connect to the USB port
 = Functions of the ports =